Joined
·
2,345 Posts
Slightly impatient waiting for the finish to dry...i suddenly need a curing booth
![Product Wood Plumbing fixture Interior design Flooring]()
Angela Super Single-ended build
61 - 79 of 79 Posts
That turned out fantastic Alan!
I think after all your prototyping, you really ended up with a great cloth.
I think after all your prototyping, you really ended up with a great cloth.
Joined
·
2,345 Posts
It is not fancy, however it is durable and sounds large...cabinet is 7 lbs on its own and 28 loaded up....
![Shipping box Wood Flooring Floor Gas]()
![Wood Electronic instrument Audio equipment Flooring Font]()
![Wood Audio equipment Gas Electronic instrument Technology]()
![Wood Cameras & optics Camera lens Audio equipment Film camera]()
![Wood Audio equipment Gas Technology Circle]()
Fuse at the bottom and pilot up top I will install tuesday...thank you nextgen for super fast shipping as always😊
Fuse at the bottom and pilot up top I will install tuesday...thank you nextgen for super fast shipping as always😊
Joined
·
2,345 Posts
Volume and tone, toggle deep and toggle vox edge
![Electronic instrument Wood Audio equipment Musical instrument Loudspeaker]()
![Light Public address system Wood Audio equipment Electronic instrument]()
![Musical instrument Electronic instrument Output device Wood Audio equipment]()
![Picture frame Wood Textile Flooring Living room]()
I really like it man and I like that it is imperfect. Looks like a piece that has been with you always.
Well done my man, well done indeed!
I adore how much it looks like an old television set.
Well done my man, well done indeed!
I adore how much it looks like an old television set.
Joined
·
2,345 Posts
No need to worry about bumping it
Joined
·
2,345 Posts
Oh yes.. she runs....i used the lower volt taps to end up with 367 plates, 355 screens, 182 pin6, 198 pin1
The speaker/cab combo adds to the perceived volume and it sounds glorious...certainly an increase in volume from a 5f2a with similar speaker/cab: so many variables that contribute
A fun build using extra pine on hand...fine for this old guy who appreciates warm and clean...cautiously I can get to 10 and control the guitar and fingers for nuances...both toggles are impressive for those who like to fiddle with switches and work fine with single coils and buckers in equal fasion
Joined
·
2,345 Posts
The thing about that style of Tone control is that the treble emphasis end of the control stops doing anything after volume is about 6 or so, while the treble-cut continues to work at any volume setting.
1965 Fender Mustang, Ampegs, anything to test an amp.
Joined
·
4,594 Posts
That will depend on the value of the tone pot...it's not noted on the schematic, probably because it is a select-on-test component, the value determining the frequency response of the inputted signal.
Joined
·
2,345 Posts
I notice this phenomenon and have pondered alteration(s); for learning experience I may install a bright cap and listen for appeal and then try a treble cut design too(probably more useful than the tweed tone circuit).
Thanks for the idea
Joined
·
2,345 Posts
I used 1meg audio on each
Joined
·
2,345 Posts
1965 Fender Mustang, Ampegs, anything to test an amp.
Joined
·
4,594 Posts
Nice retro style, Alan.
Jesus, if I turned the kitchen stove into a work bench, herself would turn a cast cooking pan into a weapon!
Joined
·
2,830 Posts
Alan saves a lot of time by eating while building amps!
My ADD just caught your guitar @Alan Small, what is that all about? Never seen anything like it before!
Joined
·
2,345 Posts
courtesy of @faracaster ..she is a Springer Guitar from France: the model is a Halfbreed with Haussel pickups and pinstriping from Europe s' top auto and cycle artist.
Made from Spanish cedar and delightful to play.
61 - 79 of 79 Posts
